If you only have a single keypad installed, you can re-program the code to use different digits than the one s that have failed. Of course, both of these options will only work for so long, and in fact may have already been done by a previous homeowner.
Buy a replacement keypad kit at Amazon. You simply remove a screw and unplug the ribbon cable, swap out the old part, and substitute the new one. You can download free alarm programming manuals through the link at the end of this page. Very few alarm hobbyists and even fewer homeowners are brave enough to fool with programming these old Napco security systems.
If you require PROM program changes, the easiest solution is to contact an alarm dealer. They can either perform the programming changes you need, or more likely recommend a newer system. Like all alarm systems, older Napco security systems will require a battery replacement about every years. These panels can all use the standard volt, sealed lead-acid SLA rechargeable alarm batteries.
As these older systems accumulate years of wear and tear, you'll reach a point when it's just not worth putting any more money into them. The good news? You may be able to re-use most of the hardwired door and window contacts, motion detectors, and sirens from the old Napco security system with a new panel and keypads.
Hardwired devices are fairly generic, and will work with almost any new panel designed to use hardwired contacts.
Depending on the age and condition of the devices, you may have to replace a few of them. But, the wiring is already in place, which is often the most difficult part of installing a hardwired system. To find a Napco alarm systems user manual, alarm installation manual, or programming guide, check out my alarm system manual sources page.
To find out how much it would cost to replace your old Napco security system, just fill out the form below. You'll receive estimates by email, with no obligation to buy anything. Magnum Alert e Control Panel pdf manual download. Magnum Alert Panel Tips Napco security systems have been protecting homes and businesses for more than 35 years. Napco Keypad Problems The Napco security systems keypads for the MA systems have a tendency to wear out after several years, specifically the buttons.
The quick and cheap solutions: If you have more than one keypad, you can swap the bad keypad with another one that is working. The not-so-quick, not-so-cheap solution: Buy a replacement keypad kit at Amazon. Battery Changes Like all alarm systems, older Napco security systems will require a battery replacement about every years. Replacing Older Napco Security Systems As these older systems accumulate years of wear and tear, you'll reach a point when it's just not worth putting any more money into them.
They are made by Napco Security Technologies, a leading manufacturer of security products ranging from intrusion and fire protection to video and access control. The company now offers many cutting edge, high tech security products, but it has its roots in much simpler technology. Many people may know the Napco alarm name from the Magnum Alert series of alarm panels. If you happen to have one of these old systems, this page is for you.
The Napco Magnum Alert line are microprocessor-based residential burglary and fire panels. They also need conductor cable to run the keypads! However, for its time, the Magnum Alert panels were a step up from the earlier 2-zone systems that came before them. It seems hard to believe now, but the earliest panels I installed only had one delay zone and one instant zone.
This made troubleshooting a bad door or window switch quite a challenge, especially on a larger house. So, you can understand what a luxury it was for me to have 4 zones to play with on the MA and MA Although they are 6-zone panels, they actually had only 4 zones available for perimeter protection.
If you happen to have an old MA panel that still works, congratulations! If your Magnum Alert system is having problems, you may still be able to keep it going for a while longer. Here are some of the most common problems, along with the best solutions I know of.
The Napco security systems keypads for the MA systems have a tendency to wear out after several years, specifically the buttons. This problem is accelerated for keypads installed outside or in a garage, where heat can cause them to fail sooner. If you have more than one keypad, you can swap the bad keypad with another one that is working.
If you only have a single keypad installed, you can re-program the code to use different digits than the one s that have failed. Of course, both of these options will only work for so long, and in fact may have already been done by a previous homeowner.
Buy a replacement keypad kit at Amazon. You simply remove a screw and unplug the ribbon cable, swap out the old part, and substitute the new one. You can download free alarm programming manuals through the link at the end of this page. Very few alarm hobbyists and even fewer homeowners are brave enough to fool with programming these old Napco security systems.
If you require PROM program changes, the easiest solution is to contact an alarm dealer.
0コメント