Page Date Programming 3. Below the cursor is the current date. Page Trouble Reminder Programming Pressing 1 while viewing Daylight Savings Screen 2 will display another screen which allows the programmer to select the month that daylight savings time will end.
In this sub-screen, pressing 1 will select September, 2 will select October and 3 will select November. Pressing 2 while viewing Daylight Savings Screen 2 will display two sub-screens which allow the programmer to select the week of the month that daylight savings time will end.
Page Ann-Bus Programming 3. Page Options Screen Programming 3. In this example, Zone 1 is the All-Call Zone. Page Onboard Dact Programming 3. Page Central Station Programming 3. Page Test Time Interval Programming 3. The Account Code screen will have a flashing cursor in the lower left corner.
Page Event Codes Programming Enter the digits as you would like the number to be dialed. Enter 9 followed by D for a three second pause or E for a five second pause then the phone number followed by an F to indicate the end of the number.
Note that Table 3. To disable event reporting, select the desired Event Code to be disabled and press 0 or Clear and then Enter to disable it. Page 96 Programming Table 3. Page 98 Programming Table 3. Page Service Terminal Programming 3. Page Supervised Phone Line Programming 3. The factory default is 0 which means the control panel will not answer an incoming call.
Page View Events Programming 3. Page Walktest Programming 3. Refer to the sections titled "Walktest" on page and "Walktest" on page for additional information regarding the Walktest feature. Page Clear Program Programming 3. Page Maintenance Programming Level Programming 3. Page Led Indicators Operating Instructions 4. Page Trouble Operation Operating Instructions 4. This block acknowledgment occurs regardless of the number of troubles, alarms and supervisory events active in the system.
Disabled NACs are held in the off state. Page Presignal Operating Instructions 4. Once a detector triggers an alarm, the onboard piezo sounds immediately, but the NACs are not activated for a user programmed time duration of up to three minutes.
A new alarm during the initial 60 second period will not cause the timer to restart with a new 60 seconds. Power is reapplied and a 17 second retard period begins which allows all detectors to stabilize. Page Read Status Operating Instructions 4. The control panel will continue to provide fire protection while in Read Status mode.
This mode can be entered while the control panel is in alarm or trouble. If a new alarm or trouble occurs during these functions, the Read Status is exited to prevent confusion. Page Input Zones Operating Instructions 4. Page Timers Operating Instructions 4. Page History Operating Instructions 4. Page Ann-Bus Operating Instructions 4. Page Central Station Operating Instructions 4.
Page Phone Line 2 Operating Instructions 4. Two supervised telephone line connections are made to interface the control panel to the telephone lines. Two optional 7 foot telephone cords are available for this purpose and can be purchased separately. Events, in terms of priority, are listed below in descending order: 1.
Alarms highest priority level Pull stations Waterflow Smoke detector Other alarm types 2. Supervisory Zone 3. Table 5. With Line Card with Rev. Future upload or download requests cause verification of the secret code by the control panel before processing of data is allowed.
If an error is detected, the block is retransmitted until correct, up to a maximum of four times. This is a four-step process, consisting of the following: 1.
Calculating the total amount of AC branch circuit current required to operate the system 2. To calculate the non-fire alarm load on the system power supply when primary power is applied, use Calculation Column 1 in Table on page Page Power Supply Calculations Table contains three columns for calculating current draws.
Full time Part time. Date Available. Salary Desired. Phone Number. Are You Over 18 years old? Yes No. Are you legally eligible for employment in the United States? Please indicate education or training which you believe qualifies you for the position you are seeking. Please list professional licenses or memberships here.
Modified Item:. Custom Bundle:. Fire Alarms. Does not apply. Visit Store: 1hallmark. Shipping and handling. This item will ship to Germany , but the seller has not specified shipping options.
Contact the seller - opens in a new window or tab and request a shipping method to your location. Shipping cost cannot be calculated. Please enter a valid ZIP Code. No additional import charges at delivery!
This item will be shipped through the Global Shipping Program and includes international tracking. Learn more - opens in a new window or tab. There are 3 items available. Please enter a number less than or equal to 3. Select a valid country. Please enter 5 or 9 numbers for the ZIP Code. Handling time. Will ship within 10 business days of receiving cleared payment.
The seller has specified an extended handling time for this item. Taxes may be applicable at checkout. Learn more. Return policy. Return policy details. Seller does not accept returns. Refer to eBay Return policy for more details. You are covered by the eBay Money Back Guarantee if you receive an item that is not as described in the listing. Payment details. Payment methods.
Select PayPal Credit at checkout to have the option to pay over time. Other offers may also be available.
0コメント